2026 Utility Trailer Flatbeds Drop Deck
- Year 2026
- Make Utility Trailer
- Model Flatbeds
2026 Utility Trailer Flatbeds Drop Deck
2026 Utility Trailer Flatbeds Drop Deck
One Step AheadOur flatbeds give you the assets that improve profitability
Built to haul heavy or awkward loads, this heavy-duty flatbed is available in all-steel and aluminum/steel combinations. Utility Drop Deck can also be custom built with a variety of options to meet your operational requirements.
Weights
GVWR
73,000 lb
Capacities
Payload Capacity
80,000 lb evenly distributed mainbeam
Dimensions
Dimensions
Kingpin location: 30" from front | Rubber dock bumpers: (2) ½" proud mounted on rear rail
Overall Length
48' 0"
Overall Height
59⅝" front deck height on 47" height 5th wheel
Overall Width
102"
Depth, Maximum
Front gooseneck: 12⅜"
Features
Features
Deck type: 21" drop with 11' 0" front deck and 40¼" rear deck height | Kingpin plate: Integral with approach plate | Kingpin type: AAR hardness cruciform | Run up members: 4 steel angles run up members | Support legs: Jost® model A400 square 2-speed steel crank type | Support leg location: 120" from leading edge of front rail to center line of support legs | Support leg shoe type: 10" × 10" hinged square low profile sand support leg shoes | Support leg crank location: Roadside of support legs || Floor type: 1⅛" extruded aluminum flat top floor with hardwood nail strips at each side rails (2) | Floor joint sealant: Caulking applied prior to assembly between aluminum planks and wood nailers | Front wall lining: ¼" exterior grade plywood | Conspicuity tape location: On rub rail | Frame finish: Utility black enamel with primer undercoat on all steel show surfaces; aluminum parts receive a natural finish | Vertical & horizontal I.C.C. bumper finish: Utility black enamel on horizontal bumper, black scharpf on vertical bumper | Bottom side rail finish: Natural aluminum | Top front & top side rail finish: Extruded aluminum | Support leg finish: Rust preventative coating | Mudflap type: Black plastic anti-sail with Utility logo, mounted with steel reinforcing straps | Slack adjusters: Bendix® Versajust® automatic | Axle manufacturer: Hendrickson® N-spindle type | Hub piloted system with outboard drums: 10 stud hub-piloted system with outboard cast drums with 16½" × 7" brakes included with ConMet Preset Plus® | Hubcaps: Federal-Mogul “non-vented”
Construction Material
Front rail: Aluminum with stainless steel front corners | Vertical and horizontal I.C.C. bumper: D.O.T. high strength steel vertical with non-slip 7" deep horizontal | Front panels: .050" pre-painted white aluminum | Front wall posts: 2" extruded aluminum Zee | Front corner post: 7 ga. formed steel
Chassis
Chassis
Coil reinforcing: Reinforcing for single 39,000 lb coil operation with 5 pairs of outriggers | Coil package reinforcement: 5' span of 4" tapered end aluminum crossmembers in coil reinforcing area on 8" center lines | Side pockets: ¼" extruded aluminum outside-type pockets on 24" center line | Crossmembers: 3" aluminum I-beam crossmembers on 12" center line full length, 28" center line over tires | Frame web: 22" deep 7 ga. steel 60,000 psi one-piece | Bottom flange: ⅝" × 4" high strength steel 80,000 psi | Top flange: 7 ga. hat section 80,000 psi high strength steel | Rub rail: ⅜" × 3" extruded aluminum with recess for conspicuity tape on sides only | Side rail: 5⅜" deep extruded aluminum with integral sliding winch track on each side | Hendrickson air ride system with integral axles: Hendrickson® AANL 23K INTRAAX air ride with LDA axles and 121" axle spacing | Axle spindle nuts: ConMet® included with Preset Plus®
Mainframe
Approach plate: ¼" steel, 45" wide, front 9" tapered up 3"
Suspension
Suspension
Fixed air ride suspension location: 96" center line to rear
Brakes
Brake System Type
Air actuation system: 1 tank with spring brakes | Air brake chambers: Bendix® EnduraSure™ 3030 | Anti-lock brake system (ABS): Bendix® TABS-6 2S/1M | Brake lining style: Hendrickson® HXS brake lining style
Wheels & Tires
Wheels
Wheel bearings: ConMet® included with Preset Plus® | 22.5" × 8.25" standard width wheels: Factory choice steel 10 hub piloted wheels | Wheel bearing lubrication: Mobilube HD Plus 80W-90 oil
Tires, Rear Specification
BFGoodrich 255/70R 22.5 ST230 16 ply, load range H | Oil seals:Curtain tensioner assembly: V-shaped furling spool mounted above a ratchet base and lock at front
Electric
Electrical
Electrical receptacle: 7-way without circuit breakers | Main harness: Utility moisture-resistant 6-wire harness with internal ground and 7-way plug
Lights and Safety
Lighting
Light weight hubs: ConMet aluminum | Stop, tail, turn lights: Grote® 4" LED (10-diode) lights, 2 per side with black snap-in flange